| (305) 825-5135

We strive our best to provide you BEST QUALITY PRODUCTS that will perform great at a LOW COST.


Our matching paint specialist has more than 35 years of experience in the field. Yes. We can match over 95 percent of all colors on the market. We use OEM formulations supplied by the top paint manufacturers to match the color code. All paint is mixed to the exact formulation at the time of order...

Read more…


It's silky smooth, lays down almost as thin as a rage extreme, doesn't pinhole,can be used as glazing putty, and sands the best out of any filler...

Read more…


Automotive sandpaper comes in a variety of different shapes, sizes and grits to be used for specific applications in the refinishing process...

Read more…


You may know how to paint, but not necessarily how to paint wood. This is because most homeowners are well-accustomed to paint-ready surfaces like wallboard, but find--much to their surprise--that painting wood is an entirely different matter. 

Read more…


How to paint wood?

You may know how to paint, but not necessarily how to paint wood. This is because most homeowners are well-accustomed to paint-ready surfaces like wallboard, but find--much to their surprise--that painting wood is an entirely different matter.

- Raw or Not? Is the wood is raw and unfinished?

- Covering Up-   If the wood has been stained or treated, or if it is already painted, then other measures need be taken. Before you get started, you'll want to be sure you have covered up the floor with newspapers, rosin paper, cardboard, plastic, or a nifty thing much like kraft paper called contractor's paper. You should also be wearing clothes you don't mind getting dirty.

- VentilationBe sure you're in a well-ventilated area. If you are working in a garage, use only water-based products. The volatile fumes from some primers and paints can pose a threat with the pilot light from your heater or hot water heater. If you must paint in the garage, take precautions by using non-flammable products as you continue.

If the Wood is Stained or Painted

If the wood you are about to paint is already stained and finished, meaning there is a clear coat of urethane or lacquer or some undisclosed finish on it, then the first step is to wash the surface with a product called TSP, which stands for Tri-Sodium Phosphate.

There are no-rinse varieties of TSP, so you might decide to use this type. The idea is that paint needs a physical or mechanical adhesion. In other words, the best way for paint to bond to the wood is to bond with the wood grain. In the case of a pre-finished surface, it impossible to bond with the wood grain.

Even worse, a pre-finished piece of wood may have other impurities on top of the finish. There will be dirt from years of use, grease from hands, or food caked on the surface, between your paint and the wood surface.

1. Sanding the Wood

After the TSP has dried and is either rinsed off or not according to instructions, the next step is to sand. Important: If your wood did not have stain or a finish on it, this is the first step in painting wood.

Do not wash down raw wood.

Even if the wood was purchased factory-direct, don't think that the wood is ready to paint; it still needs a fine sanding.

  • Get the Right Sander -
  • Start Sanding - Begin sanding with at least a fine grit of 150, though beginning with a 180 or 200 is even better. The point in sanding is not to mechanically strip the wood of the stain, but rather to simply provide the paint with something to grab. Stripping finishes--as opposed to stripping paint--is a process used only if you want to re-stain the wood, in which case stripping and bleaching will be needed.
  • Clean Wood - After sanding, thoroughly remove dust from the surface. A great way to do that is with a Shop Vac. Don't use a blower: that will only redistribute the dust back on the surface. Another great method is to use tack cloth or to wet a cloth rag with rubbing alcohol and go over the surface.


2. Priming the Wood

Why You Prime

Priming the wood prior to painting is not just an important step: this separates the professional grade paint job from amateurs. Primer is chemically formulated to bond to problem surfaces, and to give paint an even surface to bond to. It helps avoid problems such as flashing--where parts of the final paint job will look as if they were different sheens of paint. For instance, one area will look glossy, another flat, and altogether will look amateurish. Mix the primer well, and apply like you would a paint: brush, roll or spray on.

Type of Primer to Use

Depending on your final color choice, your paint manufacturer may have a particular primer base coat in mind. A properly chosen primer can really help you get your paint job done with using less paint.

Another tip to save time: have your primer tinted toward your finish color (if permitted by manufacturer's instructions). Make sure that the tinted primer is not an exact match for your eventual paint color; you just want it tinted in that direction. The reason for this is that, during the process of painting, you actually need to tell the difference between your final color and the dried primer. 

Tint alcohol Red

Wood honey tint